Automatic Transmission Components 2

With the engine running, transmission fluid is pulled into the pump section and is pushed outward by centrifugal force until it reaches the turbine section which starts it turning.  The fluid continues in a circular motion back towards the center of the turbine where it enters the stator. If the turbine is moving considerably slower than the pump, the fluid will make contact with the front of the stator fins which push the stator into the one way clutch and prevent it from turning. With the stator stopped, the fluid is directed by the stator fins to re-enter the pump at a "helping" angle providing a torque increase.   As the speed of the turbine catches up with the pump, the fluid starts hitting the stator blades on the back-side causing the stator to turn in the same direction as the pump and turbine.  As the speed increases, all three elements begin to turn at approximately the same speed.  

Since the '80s, in order to improve fuel economy, torque converters have been equipped with a lockup clutch (not shown) which locks the turbine to the pump as the vehicle speed reaches approximately 45 - 50 MPH.  This lockup is controlled by computer and usually won't engage unless the transmission is in 3rd or 4th gear.

Hydraulic System

 The Hydraulic system is a complex maze of passages and tubes that sends transmission fluid under pressure to all parts of the transmission and torque converter.  The diagram at left is a simple one from a 3-speed automatic from the '60s.  The newer systems are much more complex and are combined with computerized electrical components.  Transmission fluid serves a number of purposes including: shift control, general lubrication and transmission cooling.  Unlike the engine, which uses oil primarily for lubrication, every aspect of a transmission's functions are dependant on a constant supply of fluid under pressure.  This is not unlike the human circulatory system (the fluid is even red) where even a few minutes of operation when there is a lack of pressure can be harmful or even fatal to the life of the transmission.    In order to keep the transmission at normal operating temperature, a portion of the fluid is sent through one of two steel tubes to a special chamber that is  submerged in anti-freeze in the radiator. Fluid passing through this chamber is cooled and then returned to the transmission through the other steel tube.  A typical transmission has an average of ten quarts of fluid between the transmission, torque converter, and cooler tank.  In fact, most of the components of a transmission are constantly submerged in fluid including the clutch packs and bands.  The friction surfaces on these parts are designed to operate properly only when they are submerged in oil.

Oil Pump

The transmission oil pump (not to be confused with the pump element inside the torque converter) is responsible for producing all the oil pressure that is required in the transmission.  The oil pump is mounted to the front of the transmission case and is directly connected to a flange on the torque converter housing.  Since the torque converter housing is directly connected to the engine crankshaft, the pump will produce pressure whenever the engine is running as long as there is a sufficient amount of transmission fluid available. The oil enters the pump through a filter that is located at the bottom of the transmission oil pan and travels up a pickup tube directly to the oil pump. The oil is then sent, under pressure to the pressure regulator, the valve body and the rest of the components, as required.

Valve Body

 The valve body is the control center of the automatic transmission.  It contains a maze of channels and passages that direct hydraulic fluid to the numerous valves which then activate the appropriate clutch pack or band servo to smoothly shift to the appropriate gear for each driving situation.  Each of the many valves in the valve body has a specific purpose and is named for that function. For example the 2-3 shift valve activates the 2nd gear to 3rd gear up-shift or the 3-2 shift timing valve which determines when a downshift should occur.

The most important valve, and the one that you have direct control over is the manual valve.  The manual valve is directly connected to the gear shift handle and covers and uncovers various passages depending on what position the gear shift is placed in.  When you place the gear shift in Drive, for instance, the manual valve directs fluid to the clutch pack(s) that activates 1st gear. it also sets up to monitor vehicle speed and throttle position so that it can determine the optimal time and the force for the 1 - 2 shift.  On computer controlled transmissions, you will also have electrical solenoids that are mounted in the valve body  to direct fluid to the appropriate clutch packs or bands under computer control to more precisely control shift points.

Computer Controls

The computer uses sensors on the engine and  transmission to detect such things as throttle position, vehicle speed, engine speed, engine load, brake pedal position, etc. to control exact shift points as well as how soft or firm the shift should be.  Once the computer receives this information, it then sends signals to a solenoid pack inside the transmission.  The solenoid pack contains several electrically controlled solenoids that redirect the fluid to the appropriate clutch pack or servo in order to control shifting. Computerized transmissions even learn your driving style and constantly adapt to it so that every shift is timed precisely when you would need it.

Because of computer controls, sports models are coming out with the ability to take manual control of the transmission as though it were a stick shift, allowing the driver to select gears manually.  This is accomplished on some cars by passing the shift lever through a special gate, then tapping it in one direction or the other in order to up-shift or down-shift at will.  The computer monitors this activity to make sure that the driver does not select a gear that could over speed the engine and damage it.

Another advantage to these "smart" transmissions is that they have a self diagnostic mode which can detect a problem early on and warn you with an indicator light on the dash.  A technician can then plug test equipment in and retrieve a list of trouble codes that will help pinpoint where the problem is.

Governor,  Vacuum Modulator,  Throttle Cable

These three components are important in the non-computerized transmissions. They provide the inputs that tell the transmission when to shift.  The Governor is connected to the output shaft and regulates hydraulic pressure based on vehicle speed. It accomplishes this using centrifugal force to spin a pair of hinged weights against pull-back springs.  As the weights pull further out against the springs, more oil pressure is allowed past the governor to act on the shift valves that are in the valve body which then signal the appropriate shifts.

Of course, vehicle speed is not the only thing that controls when a transmission should shift, the load that the engine is under is also important.  The more load you place on the engine, the longer the transmission will hold a gear before shifting to the next one.

There are two types of devices that serve the purpose of monitoring the engine load: the Throttle Cable and the Vacuum Modulator.  A transmission will use one or the other but generally not both of these devices.  Each works in a different way to monitor engine load. 

The Throttle Cable simply monitors the position of the gas pedal through a cable that runs from the gas pedal to the throttle valve in the valve body.
The Vacuum Modulator monitors engine vacuum by a rubber vacuum hose which is connected to the engine.  Engine vacuum reacts very accurately to engine load with high vacuum produced when the engine is under light load and diminishing down to zero vacuum when the engine is under a heavy load.  The modulator is attached to the outside of the transmission case and has a shaft which passes through the case and attaches to the throttle valve in the valve body.  When an engine is under a light load or no load, high vacuum acts on the modulator which moves the throttle valve in one direction to allow the transmission to shift early and soft.  As the engine load increases, vacuum is diminished which moves the valve in the other direction causing the transmission to shift later and more firmly.

Seals and Gaskets

An automatic transmission has many seals and gaskets to control the flow of hydraulic fluid and to keep it from leaking out.  There are two main external seals: the front seal and the rear seal. The front seal seals the point where the torque converter mounts to the transmission case. This seal allows fluid to freely move from the converter to the transmission but keeps the fluid from leaking out.  The rear seal keeps fluid from leaking past the output shaft.

A seal is usually made of rubber (similar to the rubber in a windshield wiper blade) and is used to keep oil from leaking past a moving part such as a spinning shaft. In some cases, the rubber is assisted by a spring that holds the rubber in close contact with the spinning shaft. 

A gasket is a type of seal used to seal two stationary parts that are fastened together. Some common gasket materials are: paper, cork, rubber, silicone and soft metal.

Aside from the main seals, there are also a number of other seals and gaskets that vary from transmission to transmission. A common example is the rubber O-ring that seals the shaft for the shift control lever.  This is the shaft that you move when you manipulate the gear shifter.  Another example that is common to most transmissions is the oil pan gasket.  In fact, seals are required anywhere that a device needs to pass through the transmission case with each one being a potential source for leaks.